Sku: ERS-EYE

AUD$291.01
Availability: Many In Stock
Sku: ERS-EYE
Elecom Electronics Supply

Elsys LoRa ERS-Eye sensor - Integrated with Temperature / Humidity / Light / Room occupancy

ERS Eye is a LoRaWAN sensor that measures room occupancy. ERS Eye is designed to be mounted on a ceiling or wall. It senses the presence of body heat in the room by measuring the temperature in an 8×8 matrix with a 60×60 degree viewing angle. It can be used for dynamic workplace management, facility management and workplace statistics. The sensor also measures temperature, humidity and light.

The ERS Eye is powered by two 3,6V AA lithium battery (ER14505). The Battery life is estimated to be up to 5 years but depends on sample interval, transmit interval, data rate and environmental factors. You are welcome to use our online battery lifetime calculator. All Elsys sensors are equipped with NFC (Near Field Communication) for easy configuration with an Android phone. With our application “Sensor Settings“, you can change sample rate, data rate, encryption keys, triggers, activation and much more. All parameters can also be changed over the air from the server.  All our sensors are built on the LoRaWAN stack from Semtech. Channel plans for US902-928, EU863-870, AS923, AU915-928, KR920-923. 

 

Specifications ERS/ERS-CO2/ERS-sound

  • LoRa Alliance Certified
  • Temperature
  • Humidity
  • Light
  • Occupancy (body sense)
  • NFC for easy configuration
  • Over the air configuration
  • Size : 86x86x26mm
  • Accuracy: ± 0.5°C, ±2%rh
  • Resolution: 0.1°C, 0.1%rh
  • Approx. range: 8km*
  • Battery life: 5 years**
  • US902-928, EU863-870, AS923, AU915-928, KR920-923
  • 2 x 3.6V AA lithium battery

 

Sensor application

Sensor startup

When the sensor starts up it loads configuration from the internal memory  and merge it with user configuration. When the configuration is done the sensor writes the new configuration to the NFC chip. The sensor always writes new configurations to the NFC chip when something changes in the sensor or if NFC data is corrupted by a NFC writer or phone. The sensor always writes new configuration to NFC chip at startup. When configuration is done the sensor tries to join the network if OTAA (Over The Air Activation) is enabled.The sensor led flashes orange  when it tries to join a network. The sensor tries to join the network every 10 second and increases the join timer at every failed attempt by 10%,  up to maximum 1 hour. After startup,configuration and join the sensor enters sampling mode.

ERS

NFC read/write

When reading or writing NFC data to the sensor, it starts a timer and delays its actions for 5 seconds. This delay is for the possible bad connection inherited with NFC communication. Reasons for bad connection can be distance, location or rapid movement. After the delay, the sensor determines if the NFC data has changed or not. If the data has change the sensor reboots and starts from power up. When writing data to the sensor, try to get the best connectivity as possible. Locate the NFC antenna of the phone and sensor. Keep the 2 devices as close as possible and don’t move them while writing or reading. When you have written data to the sensor, let the sensor reboot and restart before trying to write again. You can always validate your settings by reading the NFC data after the sensor has restarted.

sensor nfc

Sampling mode

sample mode 

 

Datasheet:                    ERS EYE Datasheet.pdf

User Guide:                  ERS EYE User Guide.pdf

Setting Parameter:       ERS Setting Parameter.pdf

PayLoad:                       Uplink Payload.pdf

Downlink PayLoad:      Downlink Payload.pdf

Battery life calculator

 

 

 

ERS-EYE - Elsys room measurement LoRa sensor included Temperature/ Humidity/ Light/ Room occupancy

Sku: ERS-EYE

Just added to your wishlist:
My Wishlist
You've just added this product to the cart:
Go to cart page